The counter-intuitive fact about a Qi2 25W wireless charger program is that a passed certification report does not tell a buyer what the line will yield once magnets, coils and housings are in volume. Certification says a defined sample met the Wireless Power Consortium’s test against the current Qi2 25W specification. Production says whether the next thousand units will still align, couple and stay inside the same construction. Those are different documents.

This page is a production-tolerance and yield path for wireless OEM quality and product engineers. It is deliberately distinct from existing brand-and-distributor explainers, including the Qi2 25W wireless charging guide and the Qi2 certification and product-selection article; those pages remain the place for “what Qi2 25W is” and how to select a certified SKU. Use this page to write the line checks a resident inspector can fill. Context for the category is on wireless charging and wireless charger OEM.

What “Qi2 25W” requires on a production line that a certification report does not show

A Qi2 25W certification report shows that a defined sample was tested against the current Qi2 25W specification. It does not show magnet-array placement capability, alignment yield, or how a line will behave after a vendor or firmware change. Those production facts have to be measured on the line and written into the acceptance sheet.

The Wireless Power Consortium’s 23 July 2025 news release states that Qi v2.2.1 will be branded as Qi2 25W, and that it delivers nearly 70% more power than the original Qi2, which the same release dates to November 2023 at 15 watts. That is the rating the program is aiming at. The report that follows a certification test is still a sample result. A production line has to keep magnet polarity, array position, coil-to-housing stack and firmware inside the construction that was tested — and has to prove it with a sampling plan, not with a photocopy of the certificate.

Magnet-array placement, polarity and the yield losses buyers should ask about

Qi2’s magnetic alignment is a production characteristic, not only a user convenience. An array that is shifted, tilted, or assembled with a reversed polarity will still look complete in a cosmetic check and will still fail as “it doesn’t snap” or “it charges slowly” in the field. Buyers should ask how the line places the array (fixture, vision, or both), how polarity is verified, and what yield loss is currently attributed to magnet placement — as a figure from that line, not as an industry average this article will invent.

Do not ask the factory to quote a WPC tolerance number from memory, and do not accept a number this page might be tempted to supply. The current Qi2 / WPC documentation and the test partner’s method are the sources for any millimetre or pull-force limit. The OEM question is whether the factory has a method, a record, and a reaction plan when the method fails.

Alignment and coupling: how a line measures what a user will feel as “it just works”

What a user feels as “it just works” is alignment plus coupling: the phone seats, the session starts, and the delivered power is in the range the SKU claims for that host class. A production line can measure a seating check, a start-of-charge check, and a power or coil-current check against a documented reference receiver. It cannot substitute a single “charged my phone at the bench” demonstration for those checks.

The reference receiver and the fixture have to be controlled parts. If a line uses a random retail phone as the only alignment tool, results will drift with phone cases, battery state and operator habit. Write the reference equipment on the acceptance sheet, and keep a calibration or verification record. This is process discipline; it is not a substitute for WPC certification itself.

Black magnetic 3-in-1 wireless charging stand with a round phone pad, a watch puck and an earbud well, photographed on a white background
Magnetic alignment on a Qi2-class pad is a production characteristic: placement, polarity and a measured seating check, not only a certification logo.

Foreign-object and thermal gates that belong next to the magnet checks

Foreign-object detection and thermal behaviour belong on the same outgoing gate as the magnet checks, because a unit that snaps well and then heats a coin, or overheats a well-aligned phone, is still a yield and a field failure. The FOD method itself is the subject of a companion production article and will not be repeated here. The point on this page is sequence: magnet and alignment checks do not replace FOD or a thermal gate, and a thermal gate does not prove that the array is in the right place.

A line that only runs FOD on a daily sample, and only checks magnets when a customer complains, is not yet running a Qi2 25W production plan. Put both gates on the same sheet, with the sample sizes the program has agreed — again, not with unofficial WPC thresholds invented here.

Sampling plans for magnetic performance, not only for cosmetics

Cosmetic sampling is necessary and insufficient. A Qi2 25W OEM acceptance plan needs a magnetic-performance sample: polarity, seating, a coupling or power check, and a record of units that failed those checks and why. Incoming magnets and arrays deserve their own sample, because a new reel can be out of polarity or out of dimension before it reaches the fixture.

The sample sizes and accept/reject numbers are a contract item between the buyer and the factory. This article will not invent an AQL figure. It will say that a plan which only photographs housings is not measuring the attribute the user will feel.

Change control: a magnet vendor swap is not a free color change

A magnet vendor, a magnet grade, an array supplier, a coil vendor or a housing tool change can move alignment and coupling even when the cosmetic design looks unchanged. Those changes are not colour changes. They should reopen the magnetic-performance sample, and they may require the certification or construction file to be revisited under WPC and safety-scheme rules. The contract should say so before a purchasing team is tempted to swap a magnet for a lower quoted price.

Firmware that affects coil control or FOD is in the same class. A “small firmware update” after sample lock is a change-controlled event, not a note in a weekly meeting.

How this article differs from existing Qi2 25W brand-and-distributor explainers — and links to them

The existing Qi2 25W guide is written for brands and distributors who need to know what the rating is and how to talk about it. The certification and selection article is written for buyers choosing a certified SKU. This page assumes those questions are already in hand, and asks how a factory will keep magnet arrays and alignment inside the construction that was certified. If you are still deciding whether to specify Qi2 25W at all, start on those pages and return here to write the production sheet.

Documenting yield and capability for a private-label customer

A private-label customer is entitled to a yield and capability discussion that is specific to the SKU they will buy: incoming magnet reject rate, in-process alignment fail rate, outgoing FOD and thermal fails, and what the factory does with failed units. Those figures should come from the line, under NDA if needed, and should not be replaced by a marketing “high yield” sentence. This article will not invent a WECENT yield number.

Capability documentation can be a simple process capability record on the measured alignment or pull characteristic the factory actually uses, plus a photograph of the fixture. It does not have to be a six-sigma brochure. It does have to be repeatable when a resident inspector visits.

Black magnetic wireless charging stand with a circular phone pad facing forward, showing the charging surface a production alignment check would measure
Outgoing magnetic-performance sampling measures the surface a user will place a phone on, not only the housing colour.

Using WPC/Qi2 official documents for tolerances, never invented numbers

Any millimetre, pull-force, power or temperature limit used as a pass/fail number should come from the current WPC Qi2 25W documentation, from a test-lab method referenced to that documentation, or from a limit the buyer and factory have written into a specification and can defend. The WPC’s homepage, Qi wireless charging standard page, knowledge base and certified products database are the official entry points; this article will not transcribe unofficial tolerances. If a factory quotes a number “from Qi2” and cannot show the clause, treat it as unverified.

The same discipline applies to logo use and to the difference between a Qi2 Certified claim and a “Qi2-ready” marketing phrase. Brand-guideline questions belong on the WPC site and in the certification-selection article, not in an invented footnote here.

A production-acceptance sheet a resident inspector can actually fill

GateWhat the inspector recordsWhat is not enough
Incoming magnets / arraysLot, polarity check, dimensional or fixture check, quantity rejectedA certificate of conformance with no measurement
In-process placementFixture identity, alignment or vision result, first-off after a tool changeA statement that “operators are trained”
Outgoing magnetic performanceSeating, start-of-charge, coupling or power check against a named reference receiverOne phone from someone’s pocket
FOD and thermalCross-reference to the agreed FOD and thermal sample, with fail photosMagnet checks offered as a substitute
Change controlAny magnet, coil, housing or firmware change since the last qualified lotA verbal “same as last time”

A sheet with empty rows is a visit that found a gap. That is a more useful outcome than a signed certificate with no line data behind it.

Conclusion

Qi2 25W becomes an OEM production result when magnet arrays, alignment and yield are measured on the line, not only when a sample has a certificate. Use WPC’s current documents for any tolerance number, use existing explainer pages for what Qi2 25W is, and treat a magnet vendor swap as a change that reopens the sheet a resident inspector fills.

If you are writing a Qi2 25W production-acceptance sheet for a wireless OEM line, you can send the intended SKU and inspection scope to WECENT through the wireless charger OEM page. This is a request for a sourcing discussion, a quotation or a sample plan, not an order.

FAQ

Does a Qi2 25W certification report show what a factory’s magnet yield will be?

No. A certification report records that a defined sample was tested against the current Qi2 25W specification, as branded by the Wireless Power Consortium for Qi v2.2.1 in its 23 July 2025 news release. Yield, magnet-array placement and alignment capability are production measurements. They have to appear on an incoming and outgoing sampling plan, with a named fixture and a reference receiver. A photocopy of a certificate does not replace those records, and a private-label buyer should ask for line data on the SKU they will purchase, not for a generic “certified yield” claim.

Where should an OEM take magnet-array tolerance numbers from?

From the current Wireless Power Consortium Qi2 25W documentation, from a test laboratory’s method that references that documentation, or from a limit the buyer and the factory have written into a specification they can defend. The WPC homepage and the Qi wireless-charging standard page are the official entry points. This article does not publish unofficial millimetre or pull-force figures. If a supplier quotes a tolerance “from Qi2” and cannot show the clause or the lab method, treat the number as unverified and do not put it on a sell-sheet.

Is a magnet vendor change the same as a housing colour change?

No. A magnet vendor, magnet grade, array supplier, coil vendor or housing-tool change can move alignment and coupling even when the product looks the same. Those changes should reopen magnetic-performance sampling and may require the certification or construction file to be revisited. A colour-only change, if it does not affect the magnetic stack, is a different class of change — and even then, the factory should say so in writing, not assume it. Firmware that affects coil control belongs with the magnet-vendor class, not with cosmetics.

How does Qi2 25W relate to the original Qi2 15W rating?

The WPC’s 23 July 2025 news release states that Qi v2.2.1 will be branded as Qi2 25W and that it delivers nearly 70% more power than the original Qi2, which the same release describes as having launched in November 2023 with 15 watts of charging power. That is a standards-branding fact. It does not mean every product with a Qi2 logo is a 25W product, and it does not mean a catalog model that publishes a lower wireless wattage is a Qi2 25W SKU. An OEM should specify Qi2 25W, and evidence it, only for the exact model that will be certified and shipped at that rating.

{
“@context”: “https://schema.org”,
“@type”: “FAQPage”,
“mainEntity”: [
{
“@type”: “Question”,
“name”: “Does a Qi2 25W certification report show what a factory’s magnet yield will be?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “No. A certification report records that a defined sample was tested against the current Qi2 25W specification, as branded by the Wireless Power Consortium for Qi v2.2.1 in its 23 July 2025 news release. Yield, magnet-array placement and alignment capability are production measurements. They have to appear on an incoming and outgoing sampling plan, with a named fixture and a reference receiver. A photocopy of a certificate does not replace those records, and a private-label buyer should ask for line data on the SKU they will purchase, not for a generic “certified yield” claim.”
}
},
{
“@type”: “Question”,
“name”: “Where should an OEM take magnet-array tolerance numbers from?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “From the current Wireless Power Consortium Qi2 25W documentation, from a test laboratory’s method that references that documentation, or from a limit the buyer and the factory have written into a specification they can defend. The WPC homepage and the Qi wireless-charging standard page are the official entry points. This article does not publish unofficial millimetre or pull-force figures. If a supplier quotes a tolerance “from Qi2” and cannot show the clause or the lab method, treat the number as unverified and do not put it on a sell-sheet.”
}
},
{
“@type”: “Question”,
“name”: “Is a magnet vendor change the same as a housing colour change?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “No. A magnet vendor, magnet grade, array supplier, coil vendor or housing-tool change can move alignment and coupling even when the product looks the same. Those changes should reopen magnetic-performance sampling and may require the certification or construction file to be revisited. A colour-only change, if it does not affect the magnetic stack, is a different class of change — and even then, the factory should say so in writing, not assume it. Firmware that affects coil control belongs with the magnet-vendor class, not with cosmetics.”
}
},
{
“@type”: “Question”,
“name”: “How does Qi2 25W relate to the original Qi2 15W rating?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “The WPC’s 23 July 2025 news release states that Qi v2.2.1 will be branded as Qi2 25W and that it delivers nearly 70% more power than the original Qi2, which the same release describes as having launched in November 2023 with 15 watts of charging power. That is a standards-branding fact. It does not mean every product with a Qi2 logo is a 25W product, and it does not mean a catalog model that publishes a lower wireless wattage is a Qi2 25W SKU. An OEM should specify Qi2 25W, and evidence it, only for the exact model that will be certified and shipped at that rating.”
}
}
]
}

Related Posts