A 100 W multi-port GaN platform is not one product in three silkscreens. A 2C1A, a 2C2A and a 3C layout are three different allocation problems, three different BOMs, and often three different certification files. This page is a comparison sheet for OEM buyers who have to choose a layout. It is not a retail “best 100 W” list, and it will not invent a port map that a live product page does not publish.
Platform context is in GaN chargers, GaN charger manufacturing and sourcing, the GaN charger category, and USB-C PD and PPS.
The 100W decision: 2C1A, 2C2A and 3C as three different products, not three silkscreens
2C1A, 2C2A and 3C at 100 W are three products. Each needs its own single-port and multi-port allocation table. A silkscreen that says 100 W on every face does not make the three layouts interchangeable, and a buyer should not treat them as colour options on one BOM.
A 2C1A is usually a primary USB-C plus a second USB-C and a USB-A. A 2C2A adds a second USB-A. A 3C offers three USB-C paths and no USB-A, which changes both the accessory story and the protocol file. Those differences are product differences. They should be quoted, certified and tested as such.
| Layout | What the buyer is actually choosing | What must be in the table |
|---|---|---|
| 2C1A | A primary USB-C, a second USB-C, and a USB-A accessory path | Single-port PDOs and every claimed two- and three-port split |
| 2C2A | Two USB-C paths and two USB-A paths, a different BOM and often a different housing | The same, including USB-A behaviour under a USB-C load |
| 3C | Three USB-C paths, no USB-A, a different protocol and allocation file | Every two-port and three-port split the carton will claim |
Power-allocation tables a buyer should demand for each layout
Demand a complete allocation table for each layout: every port alone, and every combination the product will claim, in watts and in PDOs, including PPS ranges if they are required. Do not accept “100 W shared” as a row. The table is what two factories can be compared on, and what two electronic loads can later verify. This page will not invent a 100 W 2C1A, 2C2A or 3C map for a catalog model whose live page does not publish one.
Laptop-plus-peripherals: which layout actually keeps a notebook at charge
The layout that keeps a notebook at charge is the one whose written split still leaves enough power on the primary USB-C when a second and third device are attached. That figure is a charger specification, not a guess at a particular laptop’s peak. A 100 W ceiling on the housing is not a 100 W remainder on the notebook port. Write the intended remainder, test it, and choose the layout that can hold it. For how a specific computer’s maker describes recommended adapters, read that maker’s current support page, such as Apple’s note on using a power adapter with a Mac, rather than assuming a 100 W brick is sufficient for every model.
BOM and certification cost differences that a “100W” headline hides
A second USB-A, a third USB-C, a different power stage and a different housing volume are BOM differences. They are also certification differences: a new port can change the safety, EMC and USB-IF file, and a new plug variant can change a CB or national evaluation. A Union SKU may need to be named against Directive (EU) 2022/2380, and energy work against the relevant external power supply rule. The headline “100 W” hides those lines. Put them on the comparison sheet.
Desktop versus travel use, and how housing volume changes the thermal story
A compact travel housing and a larger desktop housing at the same 100 W are two thermal stories. Write a continuous-load acceptance at a stated ambient, and measure it on the sample, rather than inventing a temperature. A layout with more ports in a smaller volume is not automatically the better travel SKU if it cannot hold the written split without derating. The worksheet should say whether the SKU is intended for a bag, a desk, or both.
Cable and e-marker pairing at 100W, with a link to the kit-cable article
A 100 W path is only as useful as the cable that carries it. If a cable is in the kit, its gauge and, where the program requires one, its e-marker must match the claim on the carton. That pairing is already discussed in the article on e-marker chips and 5 A cables, and it should be a line on this comparison sheet, not an afterthought. Published USB-IF documents govern protocol behaviour; they do not, on their own, make a kit cable adequate.

Using WEG and WEP 100W catalog models only with verified port maps
Use a catalog model only with a port map that is actually on the live page, then confirm it on a sample. The WEP-100-C page, as opened for this article, describes a 100 W GaN charger with interchangeable EU, UK, US and AUS plugs, and its specification table lists Type-C output figures including 5 V/3 A, 9 V/3 A, 12 V/3 A, 15 V/3 A, 20 V/5 A and a 28 V/5 A line, at 67.8 × 66 × 32.2 mm, in white or black. The short description and the photographs on the same page also show a USB-A port. That is a discrepancy a buyer should reconcile on the current page and on a sample; this article will not invent a 2C1A or 3C map to close the gap, and it will not treat page-listed certificates, warranty or starting quantities as verified facts. A related single-port catalog entry, WEP-100-CC, lists a Type-C 100 W PDO set of 5 V/3 A, 9 V/3 A, 12 V/3 A, 15 V/3 A and 20 V/5 A on the page that was opened. WEG 100 W models, if used, should be read the same way: only with a verified map. A 140 W 3C+1A catalog example such as WEX140S is a different wattage rung, not a 100 W 3C map.
How to bench-verify a 100W split with two electronic loads
Bench-verify a claimed split with two (or three) electronic loads, at the PDOs the table advertises, and compare the result with the written map and, if a display is fitted, with the displayed numbers. Record firmware revision, ambient and cable. A single-port 100 W demonstration does not verify a multi-port claim. If the measured split collapses below the table, the sample has failed the comparison sheet, regardless of the housing mark.
Portfolio fit: 100W versus 65W and 140W in the same brand ladder
In a brand ladder, 65 W, 100 W and 140 W are different rungs, not overlapping slogans. A 65 W 2C1A workhorse covers a different remainder under a second load than a 100 W multi-port, and a 140 W 3C+1A platform, such as the WEX140S page that states 140 W on USB-C1 and published splits at that higher ceiling, is a further step. Choose the rung on the written remainder and the intended device set, not on a desire to print a larger number.

Red flags: “100W shared” that collapses to 30W+30W under two laptops
A red flag is a “100 W shared” claim that, under two loads, collapses to a split that will not keep two notebooks, or even one notebook and a peripheral, at the remainder the buyer intended: for example a 30 W+30 W collapse under two laptops. That is a different product from a 100 W brick with a written, tested split. Refuse the headline, require the table, and measure it. If the factory cannot produce the table, it cannot quote the layout.
Conclusion
Choose a 100 W multi-port layout as a product — 2C1A, 2C2A or 3C — with a complete allocation table, a kit-cable line, and a bench check against two electronic loads. Use WEP and WEG catalog models only with verified maps, and treat a “100 W shared” headline that collapses under two loads as a red flag, not as a bargain.
If your team is comparing 100 W multi-port layouts for an OEM catalog and wants to discuss a specific allocation scope, you can send that scope through the GaN charger manufacturing and sourcing page. This is a request for a project discussion.
FAQ
Can I use a 100W charger for a MacBook Pro?
A 100 W charger is a ceiling, not a guarantee that it matches the adapter recommended for a given MacBook Pro. Apple states that a Mac which charges over USB-C can charge from a USB-C adapter that supports USB Power Delivery, including third-party adapters that meet applicable safety standards, and that the adapter should provide at least the recommended wattage for that Mac. Recommended adapters differ by model; some 16-inch models are described with a 140 W adapter. Read Apple’s current support page for the specific model.
Can I charge OnePlus with any charger?
This article will not invent which protocols a given OnePlus model accepts, including any proprietary fast-charge path. Whether a phone will negotiate USB Power Delivery, or another protocol, is a fact on the device maker’s current specification for that model, and on a measurement with the intended charger and cable. “Any charger” is not a specification. For an OEM 100 W program, write the charger’s PDO and allocation table, and let the device take what it negotiates; do not assume a handset brand’s marketing name is the same as a USB PD claim.
Which phone has 300W charging?
This article will not identify a phone model as having 300 W charging. Peak-wattage claims belong on the device maker’s current specification, they change, and they are not a reason to specify a charger from a headline. A 100 W multi-port OEM platform should be compared on its written allocation table and on a bench measurement, not on a consumer peak that a particular handset may or may not advertise. If a program genuinely needs a higher ceiling, that is a different rung, such as a 140 W platform, with its own verified map.
Is it safe to use a GaN charger?
Gallium nitride is a semiconductor material in the power stage. Safety is a matter of certified design, insulation, protection circuits and the applicable standard edition, not of the material name. A GaN charger is not safe merely because it is GaN, and a silicon charger is not unsafe merely because it is not. For an OEM program, safety is the file: the standard edition, the report, the outgoing hipot and electrical tests, and a layout whose written split has been measured. Ask for that evidence; do not treat “GaN” as a safety claim.
{
“@context”: “https://schema.org”,
“@type”: “FAQPage”,
“mainEntity”: [
{
“@type”: “Question”,
“name”: “Can I use a 100W charger for a MacBook Pro?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “A 100 W charger is a ceiling, not a guarantee that it matches the adapter recommended for a given MacBook Pro. Apple states that a Mac which charges over USB-C can charge from a USB-C adapter that supports USB Power Delivery, including third-party adapters that meet applicable safety standards, and that the adapter should provide at least the recommended wattage for that Mac. Recommended adapters differ by model; some 16-inch models are described with a 140 W adapter. Read Apple’s current support page for the specific model.”
}
},
{
“@type”: “Question”,
“name”: “Can I charge OnePlus with any charger?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “This article will not invent which protocols a given OnePlus model accepts, including any proprietary fast-charge path. Whether a phone will negotiate USB Power Delivery, or another protocol, is a fact on the device maker’s current specification for that model, and on a measurement with the intended charger and cable. “Any charger” is not a specification. For an OEM 100 W program, write the charger’s PDO and allocation table, and let the device take what it negotiates; do not assume a handset brand’s marketing name is the same as a USB PD claim.”
}
},
{
“@type”: “Question”,
“name”: “Which phone has 300W charging?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “This article will not identify a phone model as having 300 W charging. Peak-wattage claims belong on the device maker’s current specification, they change, and they are not a reason to specify a charger from a headline. A 100 W multi-port OEM platform should be compared on its written allocation table and on a bench measurement, not on a consumer peak that a particular handset may or may not advertise. If a program genuinely needs a higher ceiling, that is a different rung, such as a 140 W platform, with its own verified map.”
}
},
{
“@type”: “Question”,
“name”: “Is it safe to use a GaN charger?”,
“acceptedAnswer”: {
“@type”: “Answer”,
“text”: “Gallium nitride is a semiconductor material in the power stage. Safety is a matter of certified design, insulation, protection circuits and the applicable standard edition, not of the material name. A GaN charger is not safe merely because it is GaN, and a silicon charger is not unsafe merely because it is not. For an OEM program, safety is the file: the standard edition, the report, the outgoing hipot and electrical tests, and a layout whose written split has been measured. Ask for that evidence; do not treat “GaN” as a safety claim.”
}
}
]
}
